Skip to main content

Posts

Nifty 50

Recent posts

Decoration Lamp

Decoration Lamp Take a wooden ply piece of dimension 190mm x 120mm x 19mm and cover it with laminates. Take another 3 piece of  dimension (270mm x 100mm x 19mm) x 2 and 290mm x 60 mm x 5mm plyboard. Take 5mm thickness plyboard and sandwich it between 19mm thickness board. Keep some space around it as the 5mm plyboard is small in width. Now, Take the sandwich piece and laminate it on both side. Take smaller piece (190mm x 120mm ) and drill three holes - Two for screw and One for Wire to pass through. Joint the upper part with lower part. For cleaness apply paint to corner for better look. The grove left is for led strip (12 volts). Pass the wire through the hole we left, and cover 3/4 side with led strip. Finished Product.  Watch & Subscribe

Wooden Desk Lamp

DIY Wooden Desk Lamp First of all make triangle base of dimension 150mm x 90mm x 19mm board. Then take two wooden pieces of dimension 430mm x 50mm and 300mm x 50mm. Take smaller piece (300mm x 50mm) and cut the end at 70 degree both side but opposite to each other. Now take larger piece (430mm x 50mm) and make grove into it for led placement. Take smaller piece (300mm x 50mm) and make a grove behind it and insert pipe for wiring to pass through and then seal it with wood filling. Place led strip in to grove and cover it with acrylic sheet, pass wire through the pipe (inserted in samller wood) and then to the base. Attach the top wood to the smaller wooden piece and together attach them to wooden base piece. Fill all the voids with woodfilling and then sand it with fine sand paper for better result. Then apply some paint on it and you are ready to go... Finshed Product... Watch & Subscribe

CNC Micro Engraving Machine - EleksMaker

CNC Micro Engraving Machine - EleksMaker  See More Details -  Click Here Brand EleksMaker Model EleksMill Axial Triaxial Laser Power 500mw Laser Wavelength 445nm-450nm Dimensions 260 × 260 × 260mm Working Area 130× 90 × 40mm Packag Weight 5.5kg Communication Interface MiniUSB Interface Control Board EleksMana Stepper motor 1.3A 42 stepper motor Power choice 12V 5A above Software Support GRBL/ Candle (CNC), Benbox/EleksCAM(laser) Certification CE ,FCC ,FDA(Please contact us if you need them) Features: 1. This product not only can be used as CNC Micro Engraving Machine, and with a 500mw Laser Module, can be used as a laser engraving machine. 2. Two functions can be switched with each other, allowing you to work even easier. 3. Make of Aluminum material,durable and solid,Adjustable focal length, to wood carving, you can use the NC and so on. 4. Main purpose: wooden plaque engraving, laser engraving, PCB sculpture, acrylic sculptu...

DIY Gaming Desk

DIY Gaming Desk  I was felling uncomfortable with my old table so, I started to make it my self. This table is 4 foot by 2 foot on the top shelves and has 5 inches overhang on all over four side. This is the overview of the under shelves skeleton. It's dimension are 38 inch, 32 inch, 16 inch, 16 inch as shown in the figure above. This is the table legs which are 31 inch long as shown in the figure above. This the table leg part whose dimensions are 3 inch up from the bottom and 5 inch down from the upper edge of table leg. This is the lower edge table space around the table for  cable management  which is 5 inch lower from the table top.   This is the table top whose dimensions are  48 inch x 24 inch

Cement Stand

Cement Stand This is a cement candle holder and decoration piece (DIY Project) To Make cement candle holder take a piece of cardboard an cut it and fold it around like candle size shape, and fill it with POP (Plaster Of Paris). Take out the candle shape from the cardboard mould, sand the rough edges little bit with sandpaper, then place them inside the box at equal distance.  Now Pour some cement mix and let it dry and the take out the POP mould and place the candle into cement holder and light them...! Enjoy Watch the video for more details...

Led Cube

LED CUBE  This is Led Cube made of Cement Block on both side up and down with in between acrylic square.  First, of all make a two cardboard square of  7 cm x 7 cm for cement mould. Also place a pipe in the cement block for wiring.  Then, Make led circuit board of 4 to 6 leds.  Cut some acyrlic pieces of size 7 cm x 4 cm and then sand it with micro sand paper or a diffuse shade. Take out the cement square from the mould, sand little bit for finishing look.   Place led board in the center of cement square, attach the acylic square to the cement square with the  help of hot glue.And that's all Light it...! Watch the video for more details....